Property History

554 ALLEN (RES) -- Basement Level – Finishing and Renovation, Frame and finish existing unfinished basement area (1430 SQFT) and construct new interior walls where necessary, ceilings, soffits and other surfaces as required to accommodate the proposed layout. 1. Construct a new full bathroom, including plumbing rough-in, fixture installation, and associated finishes. 2. Install a wet bar, including cabinetry, countertop, sink, and required plumbing and electrical connections. 3. Modify existing exterior wall openings, including converting the existing exterior door opening to a window opening and installing new window assemblies as shown on the proposed elevations. New window width rough opening will not be greater than current door rough opening. 4. Modify the existing exterior window openings to accommodate new French doors, including required framing, structural support, flashing, weatherproofing, and exterior masonry repairs. New door width rough opening will not be greater than current window rough opening. 5. Perform necessary electrical, plumbing, mechanical, and ventilation modifications to serve the renovated spaces per applicable local, state and national building codes. 6. Complete drywall, painting, trim, and other associated interior finishes. 7. Install designated flooring, including luxury vinyl plank (LVP), and complete associated trim and finish work. Main Floor – Interior Remodeling 1. Perform selective demolition of existing finishes and building components as required for the proposed remodeling. 2. Perform required framing and structural modifications associated with the proposed kitchen opening, including installation of engineered or reinforced support components. Proposed opening is 126”. 3. Remove existing non-load bearing decorative columns between living room and breakfast area and finish disturbed area. 4. Convert existing powder room into a full bathroom by consolidating adjacent passage way into a shower. Perform associated plumbing, electrical, and other building-system modifications necessary to accommodate the proposed layout and fixtures. 5. Remove and replace kitchen island cabinetry and countertop. 6. Renovate the laundry and mudroom areas, including associated finish and fixture modifications. Remove and replace laundry room cabinetry and countertop. 7. Complete drywall repairs, painting, and other finish work associated with the renovation. Second Floor – Bathrooms (three) 1. Remove existing bathtub and shower enclosures in all three bathrooms. Complete the proposed shower and bathtub modifications, including waterproofing, tile installation, and installation of the specified shower glass enclosure. 2. Remove existing vinyl flooring in all bathrooms and replace with porcelain tiles. 3. Removal and Replacement of code compliant fixtures 4. Complete drywall repairs, painting, and other finish work associated with the renovation. General Construction Requirements 1. Perform all work in accordance with the approved construction documents and applicable building codes. 2. Provide required framing, structural supports, flashing, waterproofing, and weatherproofing associated with the approved modifications. 3. Complete plumbing, electrical, mechanical, and ventilation work in accordance with applicable codes and required permits. 4. Maintain required structural integrity, fire safety, and emergency egress provisions. 5. Coordinate required inspections with the local building department. 6. Repair and restore surfaces affected by the construction work. 7. Remove construction debris and clean affected areas upon completion. The project is an alteration and renovation of an existing single-family residence. No increase in the building footprint is proposed unless specifically indicated on the approved construction documents.

Reported project value $84,000

Scope Code R1 Single Family Residence

Application Square Footage 1430

Professionals on this permit Tamtru Construction LLC (General contractor)

554 ALLEN (RES) -- Basement Level – Finishing and Renovation, Frame and finish existing unfinished basement area (1430 SQFT) and construct new interior walls where necessary, ceilings, soffits and other surfaces as required to accommodate the proposed layout. 1. Construct a new full bathroom, including plumbing rough-in, fixture installation, and associated finishes. 2. Install a wet bar, including cabinetry, countertop, sink, and required plumbing and electrical connections. 3. Modify existing exterior wall openings, including converting the existing exterior door opening to a window opening and installing new window assemblies as shown on the proposed elevations. New window width rough opening will not be greater than current door rough opening. 4. Modify the existing exterior window openings to accommodate new French doors, including required framing, structural support, flashing, weatherproofing, and exterior masonry repairs. New door width rough opening will not be greater than current window rough opening. 5. Perform necessary electrical, plumbing, mechanical, and ventilation modifications to serve the renovated spaces per applicable local, state and national building codes. 6. Complete drywall, painting, trim, and other associated interior finishes. 7. Install designated flooring, including luxury vinyl plank (LVP), and complete associated trim and finish work. Main Floor – Interior Remodeling 1. Perform selective demolition of existing finishes and building components as required for the proposed remodeling. 2. Perform required framing and structural modifications associated with the proposed kitchen opening, including installation of engineered or reinforced support components. Proposed opening is 126”. 3. Remove existing non-load bearing decorative columns between living room and breakfast area and finish disturbed area. 4. Convert existing powder room into a full bathroom by consolidating adjacent passage way into a shower. Perform associated plumbing, electrical, and other building-system modifications necessary to accommodate the proposed layout and fixtures. 5. Remove and replace kitchen island cabinetry and countertop. 6. Renovate the laundry and mudroom areas, including associated finish and fixture modifications. Remove and replace laundry room cabinetry and countertop. 7. Complete drywall repairs, painting, and other finish work associated with the renovation. Second Floor – Bathrooms (three) 1. Remove existing bathtub and shower enclosures in all three bathrooms. Complete the proposed shower and bathtub modifications, including waterproofing, tile installation, and installation of the specified shower glass enclosure. 2. Remove existing vinyl flooring in all bathrooms and replace with porcelain tiles. 3. Removal and Replacement of code compliant fixtures 4. Complete drywall repairs, painting, and other finish work associated with the renovation. General Construction Requirements 1. Perform all work in accordance with the approved construction documents and applicable building codes. 2. Provide required framing, structural supports, flashing, waterproofing, and weatherproofing associated with the approved modifications. 3. Complete plumbing, electrical, mechanical, and ventilation work in accordance with applicable codes and required permits. 4. Maintain required structural integrity, fire safety, and emergency egress provisions. 5. Coordinate required inspections with the local building department. 6. Repair and restore surfaces affected by the construction work. 7. Remove construction debris and clean affected areas upon completion. The project is an alteration and renovation of an existing single-family residence. No increase in the building footprint is proposed unless specifically indicated on the approved construction documents.

554 Allen RD NE, 30324 -- To Whom It May Concern: Please find attached the stamped structural engineering letter prepared by Mason Peterson, [PE042468], of Skywark Engineering, P.C., addressing the removal of a load-bearing partition wall located between the kitchen and dining room at the above-referenced property. The attached letter specifies the structural support method required to safely transfer the loads previously carried by the removed wall. Per current Office of Buildings policy, this office is not reviewing structural drawings at this time; responsibility for the design's code compliance rests with the Engineer of Record, as noted in the attached document. This submission also includes removal of one additional non-load-bearing interior partition wall, which does not require structural modification and is included here for completeness of the renovation scope. Please contact me at 615-491-2297 or tudoji@gmail.com with any questions regarding this submission. Sincerely, Timothy Udoji